Drilling Mud Additives – Mud Expert

Start with the mud system and the field measurements when selecting drilling mud additives. Poor hole cleaning can result from insufficient annular velocity or a loss of low-shear carrying capacity. Adding a viscosifier may raise pump pressure while leaving the cause unresolved. Define the performance target first, then compare candidates in the same base mud.

Match the additive to the field problem

  • Shale hydration and dispersion. In water-based mud, evaluate partially hydrolyzed polyacrylamide (PHPA) for cuttings encapsulation or compare suitable grades of potassium polyacrylate (K-PAM). Use representative cuttings in hot-roll recovery or dispersion tests and check compatibility and rheology.
  • High fluid loss. For water-based systems, compare drilling-grade polyanionic cellulose (PAC), carboxymethyl cellulose (CMC), and other polymer fluid-loss reducers. Record filtrate volume, filter-cake condition, and rheology under test conditions that reflect the project’s temperature and salinity.
  • Poor cuttings transport or solids suspension. Evaluate xanthan gum in water-based mud or organophilic bentonite in oil-based mud. Read low-shear measurements and gel strengths alongside annular velocity, cuttings returns, and equivalent circulating density. Weighting materials adjust mud density and add solids, which can affect sag and rheology.
  • Unstable oil-based emulsion. Check the oil-to-water ratio, internal-phase salinity, and solids loading before evaluating a primary and secondary emulsifier package or a suitable combined emulsifier. Review electrical stability trends alongside rheology and high-temperature, high-pressure filtration.
  • Rising torque or drag. Check well trajectory, cuttings-bed indicators, and hole cleaning. If a lubricant is appropriate, test lubricity and compatibility and measure the effects on filtration and rheology.

Compare samples under the same conditions

Keep an untreated base-mud sample as a control. Use the same mixing sequence, shear, aging, and test conditions for each candidate. Record the dose and measurements before and after aging. Compare the improvement in the target property with changes elsewhere in the mud profile. During a field trial, follow the project’s treatment procedure and monitor the mud properties over subsequent circulations.

What to include in a supplier inquiry

Share the mud type, target density, temperature and salinity ranges, the problem you are seeing, and the test method and acceptance criteria. For international orders, include the estimated quantity, packing requirements, destination, and required delivery window. Contact Puyang Jinxiang Chemical for grade-specific technical and safety data sheets and a sample for testing in your base mud.

A practical laboratory screening sequence

  1. Establish the baseline. Retain an untreated sample and record density, rheology, filtration, pH, salinity and solids loading. Note the instruments and test temperature.
  2. Choose one priority. Define whether the main goal is lower fluid loss, better cuttings integrity or improved low-shear suspension. Avoid changing several additives at once in the first comparison.
  3. Test a dose range. Compare the blank with candidate doses in the same base mud. Keep the mixing order and aging conditions consistent, then remeasure the target and secondary properties.
  4. Run a controlled field trial. Follow the project’s treatment procedure and track mud properties, pump pressure and hole-cleaning indicators over subsequent circulations.

Frequently asked questions

What does PAC mean in a drilling-fluid inquiry?

In drilling fluids, PAC normally means polyanionic cellulose, a polymer used for fluid-loss control and rheology. In water treatment, PAC often means polyaluminium chloride, a coagulant. Specify the full chemical name and intended application on the inquiry and technical documents.

Can a product be selected by one test result?

A single result is insufficient. Freshwater, brine, temperature and solids loading can change an additive’s behavior, while improving one property can affect another. Select the grade and dose using representative base mud, agreed test methods and a controlled field trial.

Related resources: 水基钻井液解决方案, 油基钻井液解决方案 and Polyanionic Cellulose PAC-LV.

发表回复

您的邮箱地址不会被公开。 必填项已用 * 标注